Linux version 2.6.22.19-19-4 (andy@SVN-server) (gcc version 4.3.2 (Sourcery G++ Lite 4.3-51) ) #7 PREEMPT Tue Apr 27 18:56:01 CST 2010
Physical map 0x80000000 to 0x04000000, max remap/kernel size: 0x0c000000/0x18000000.
Configured for SMP865x, detected SMP8655 (revision unknown).
Detected CPU/System/DSP Frequencies: 499.50/333.00/333.00MHz
SMP86xx Enabled Devices under Linux/XENV 0x8e69bcb0 = 0x001b3efc
 PCIHost Ethernet Ethernet1 IR FIP I2CM I2CS USB PCIDev1 PCIDev2 PCIDev3 PCIDev4 SATA SCARD SCARD1
CPU revision is: 0001937c
FPU revision is: 01739300
Determined physical RAM map:
 memory: 05000000 @ 04000000 (usable)
User-defined physical RAM map:
 memory: 06400000 @ 04000000 (usable)
Wasting 131072 bytes for tracking 4096 unused pages
Initrd not found or empty - disabling initrd
On node 0 totalpages: 10496
  DMA zone: 20 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 10476 pages, LIFO batch:1
  Normal zone: 0 pages used for memmap
Built 1 zonelists.  Total pages: 10476
Kernel command line: console=ttyS0 mem=100M
Primary instruction cache 32kB, 4-way, physically tagged, linesize 32 bytes.
Primary data cache 32kB, 4-way, physically tagged, no aliases, linesize 32 bytes
Synthesized TLB refill handler (20 instructions).
Synthesized TLB load handler fastpath (32 instructions).
Synthesized TLB store handler fastpath (32 instructions).
Synthesized TLB modify handler fastpath (31 instructions).
Cache parity protection disabled
PID hash table entries: 1024 (order: 10, 4096 bytes)
Using 249.750 MHz high precision timer.
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 3, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 2, 65536 bytes)
Memory: 96256k/102400k available (3506k kernel code, 6080k reserved, 797k data, 704k init, 0k highmem)
Calibrating delay loop... 332.59 BogoMIPS (lpj=1662976)
Mount-cache hash table entries: 2048
NET: Registered protocol family 16
PCI: Initializing SMP86xx PCI host controller
PCI: Remapped PCI I/O space 0x58000000 to 0xc0000000, size 64 kB
PCI: Remapped PCI config space 0x50000000 to 0xc0018000, size 10 kB
PCI: Configured SMP86xx as PCI slave with 1024MB PCI memory
PCI: Region size is 131072KB
PCI: Map DMA memory 0x04000000-0x0a400000 for PCI at 0x48000000
SCSI subsystem initialized
libata version 2.21 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Time: TANGOX clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 0, 16384 bytes)
TCP established hash table entries: 8192 (order: 2, 65536 bytes)
TCP bind hash table entries: 8192 (order: 1, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
NTFS driver 2.1.28 [Flags: R/O].
fuse init (API version 7.8)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
tango3dog: Hardware Watchdog Timer for SMP864x/SMP865x 0.1 (def. timeout: 30 sec)
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 9) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 10) is a 16550A
loop: module loaded
tangox_enet0: unable to autodetect phy
tangox_enet1: detected phy  at address 0x01
tangox_enet1: Ethernet driver for SMP864x/SMP865x internal MAC core 1: 100Mbps Base at 0x26800
tangox_enet1: mac address 00:d0:4b:89:e1:c1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
tangox_bmide: bmide support is disabled
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
driver tangox-ehci-hcd, 10 Dec 2004
TangoX USB initializing...
tangox-ehci-hcd tangox-ehci-hcd: TangoX USB 2.0
tangox-ehci-hcd tangox-ehci-hcd: new USB bus registered, assigned bus number 1
tangox-ehci-hcd tangox-ehci-hcd: irq 48, io mem 0xa0021400
tangox-ehci-hcd tangox-ehci-hcd: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
tangox-ohci-hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
TangoX USB was initialized.
Initializing TangoX USB OHCI Controller Membase=0xa0021500, irq=47
tangox-ohci-hcd tangox-ohci-hcd: USB Host Controller
tangox-ohci-hcd tangox-ohci-hcd: new USB bus registered, assigned bus number 2
tangox-ohci-hcd tangox-ohci-hcd: irq 47, io mem 0xa0021500
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-2: new high speed USB device using tangox-ehci-hcd and address 2
usb 1-2: configuration #1 chosen from 1 choice
scsi0 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Freeing unused kernel memory: 704k freed
sigmablock: module license 'Proprietary' taints kernel.

CS 0 vendor id 0xec.......
CS 0 device id 0xf1.......
................................................................................................................................................................................................................................................................

********************** Parition configureations for CS 0 *******************
**** parition 1  offset [0x00000000] + size [0x00080000] = [0x00080000] ****
**** parition 2  offset [0x00080000] + size [0x00040000] = [0x000c0000] ****
**** parition 3  offset [0x000c0000] + size [0x00300000] = [0x003c0000] ****
**** parition 4  offset [0x003c0000] + size [0x00300000] = [0x006c0000] ****
**** parition 5  offset [0x006c0000] + size [0x01000000] = [0x016c0000] ****
**** parition 6  offset [0x016c0000] + size [0x00800000] = [0x01ec0000] ****
**** parition 7  offset [0x01ec0000] + size [0x01dc0000] = [0x03c80000] ****
**** parition 8  offset [0x03c80000] + size [0x01dc0000] = [0x05a40000] ****
**** parition 9  offset [0x05a40000] + size [0x00020000] = [0x05a60000] ****

 !!!!! invalid parition 9 *** offset [0x05a40000] + size [0x00020000] = [0x05a60000] > available space 0x05a40000 ***

**** parition 10  offset [0x05a60000] + size [0x00020000] = [0x05a80000] ****

 !!!!! invalid parition 10 *** offset [0x05a60000] + size [0x00020000] = [0x05a80000] > available space 0x05a40000 ***

**** parition 11  offset [0x05a80000] + size [0x00020000] = [0x05aa0000] ****

 !!!!! invalid parition 11 *** offset [0x05a80000] + size [0x00020000] = [0x05aa0000] > available space 0x05a40000 ***

chip_index 0 pos 0

CS 1 vendor id 0x00.......
CS 1 device id 0x00.......
nand_probe Error on chip 1 ret code -13
scsi 0:0:0:0: Direct-Access     Generic  USB  SD Reader   0.00 PQ: 0 ANSI: 2
sd 0:0:0:0: [sda] 3936256 512-byte hardware sectors (2015 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
sd 0:0:0:0: [sda] 3936256 512-byte hardware sectors (2015 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: [sda] Attached SCSI removable disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete
em8xxx: no version for "llad_open" found: kernel tainted.
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1571] init_module: begun
em8xxx0 [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1431] identify: board as unknown subid
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1557] identify: device 0x8655 0x5 accepted with software tango3ES3
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1636] mumk_register_tasklet 0xc009c000
mumk_register_tasklet: (0) tasklet c009c000 status @c0205f74
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[0] 0xc00a4000: pE=0xc0205d50 ch_idx=33 module_id=0x3c 0xc0205d70
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[1] 0xc00ac000: pE=0xc0205d50 ch_idx=35 module_id=0x3c 0xc0205d7c
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[2] 0xc00b4000: pE=0xc0205d50 ch_idx=41 module_id=0x13c 0xc0205d88
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[3] 0xc00bc000: pE=0xc0205d50 ch_idx=43 module_id=0x13c 0xc0205d94
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[4] 0xc00c4000: pE=0xc0205d50 ch_idx=37 module_id=0x23c 0xc0205da0
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[5] 0xc00cc000: pE=0xc0205d50 ch_idx=39 module_id=0x23c 0xc0205dac
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:353] mumk_register_channel_tasklet[6] 0xc00d4000: pE=0xc0205d50 ch_idx=69 module_id=0x3f 0xc0205db8
em8xxx [/var/andy/LMP555/Mini_2.02.02/src/libs/3_7_0/mrua_SMP8654F_3_7_1_rc_3_dev.mips/MRUA_src/rua/emhwlib_kernel/kernel_src/krua.c:1733] init_module: done. Found 1 em8xxx
ir: cannot get major number
SMP86xx ir (253:0): driver loaded (wait_period = 30ms, buffer_size = 2)
led_rst: cannot get major number
led_rst: cannot get major number
SMP865x LMP GPIO: led_rst(252:0) driver loaded.
Tuxera NTFS driver 3010.3.18 [Flags: R/W MODULE].
Tango3 frequency scaling module installed, (standby mode supported).
i2c_hal_init_module
HW_I2C_REG: 0x10480 = 0
g751_init_module
NOT found G751 thermal sensor IC!
Warnning: someone change the HW_I2C_REG setting!
ir: Enable NEC decoder (0x00000000)
ir: Enable RC5 decoder (0x00000000)
Warnning: someone change the HW_I2C_REG setting!
usb_device usbdev2.1: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev2.1_ep81: uevent: unsupported action-string; this will be ignored in a future kernel version<3>hub 2-0:1.0: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev2.1_ep00: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb usb2: uevent: unsupported action-string; this will be ignored in a future kernel version<3>tangox-ohci-hcd tangox-ohci-hcd: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_device usbdev1.2: uevent: unsupported action-string; this will be ignored in a future kernel version<3>sd 0:0:0:0: uevent: unsupported action-string; this will be ignored in a future kernel version<3> target0:0:0: uevent: unsupported action-string; this will be ignored in a future kernel version<3> host0: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev1.2_ep82: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev1.2_ep01: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb-storage 1-2:1.0: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev1.2_ep00: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb 1-2: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_device usbdev1.1: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev1.1_ep81: uevent: unsupported action-string; this will be ignored in a future kernel version<3>hub 1-0:1.0: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb_endpoint usbdev1.1_ep00: uevent: unsupported action-string; this will be ignored in a future kernel version<3>usb usb1: uevent: unsupported action-string; this will be ignored in a future kernel version<3>tangox-ehci-hcd tangox-ehci-hcd: uevent: unsupported action-string; this will be ignored in a future kernel version<3>tty ttyS1: uevent: unsupported action-string; this will be ignored in a future kernel version<3>tty ttyS0: uevent: unsupported action-string; this will be ignored in a future kernel version<3>serial8250 serial8250: uevent: unsupported action-string; this will be ignored in a future kernel version<3> platform: uevent: unsupported action-string; this will be ignored in a future kernel versionk_name=Tangox SATA 0 driver=Tangox SATA 0
SATA version 0x3139302a ID 0x0 is detected
scsi1 : Tangox SATA 0
ata1: SATA max UDMA/133 cmd 0xa0023000 ctl 0xa0023020 bmdma 0xcdcdcdcd irq 49
sd 0:0:0:0: [sda] 3936256 512-byte hardware sectors (2015 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 0:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
ata1: SATA link down (SStatus 0 SControl 300)
k_name=Tangox SATA 1 driver=Tangox SATA 1
SATA version 0x3139302a ID 0x0 is detected
scsi2 : Tangox SATA 0
ata2: SATA max UDMA/133 cmd 0xa0023800 ctl 0xa0023820 bmdma 0xcdcdcdcd irq 62
ata2: SATA link down (SStatus 0 SControl 300)
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
eth0: link down
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1